INERGEK
INDUSTRIAL ENGINEERING & CONNECTIVITY
部品番号
SBRS-(4X)GRH
デュアルウォール製品

4:1 shrink ratio High-Shrink-Ratio, High Temperature Resistant, Adhesive-Lined ,Polyolefin Heat Shrink Tubing

SBRS-(4X)GRH

High-Shrink-Ratio, High Temperature Resistant, Adhesive-Lined ,Polyolefin Heat Shrink Tubing

It consists of a double layer of cross-linked polyolefin and polyamide PA. The product has high shrinkage and wear resistance characteristics, and is widely used in high temperatureenvironments such as wiring harnesses inside automotive engine compartments, electrical connections to electronic equipment, and other occasions where sealing is required.

It consists of a double layer of cross-linked polyolefin and polyamide PA. The product has high shrinkage and wear resistance characteristics, and is widely used in high temperatureenvironments such as wiring harnesses inside automotive engine compartments, electrical connections to  electronic equipment, and other occasions where sealing is required.

07   SBRS-(4X)G.png


Features

● 4:1 shrink ratio allows for fewer sizes to cover numerous splice configurations and diameters.

● The  hot melt adhesive is made of polyamide PA material, with  high temperature resistance 

   (no dripping  at 125 ℃), strong permeability, and strong sealing performance

● Thick adhesive liner forms an effective barrier against fluids and moisture penetration.

● Minimum shrink temperature: 70°C .

● Continuous operating temperature: -45°C to 125°C .

● Fully shrink temperature:125℃.

● Standard color: black , clear (other colors can be customized).


​Technical Data

PropertyTest MethodStandard
Tensile Strength(MPa)ASTM D2671≥10.4
Elongation(%)ASTM D2671≥200
Tensile Strength after aging (MPa)ASTM D 2671(158℃×168h)≥7.3
Elongation after aging(%)ASTM D 2671(158℃×168h)​≥100
Dieletric strength(kV/mm)IEC 60243≥15
Volume resistivity(Ω.cm)ASTM D876≥1X1014

Adhesive

PropertyTest MethodStandard
Water AbsorptionASTM D570<0.2%
Sofening Point (℃) ASTM E2895±5
Strength of peeling(PE) ASTM D 1000120N/25mm
Strength of peeling(AL)ASTM D 100080N/25mm


Specification Table

Dimensions

SizeExpandedAfter Recovery
mm

Inner Diameter

Min(mm)

Inner Diameter

Max(mm)

Total Wall 

Thickness(mm)

Adhesive 

Thickness(mm)

Φ4.00

4.00

0.95

1.40±0.30

0.70±0.20

Φ5.75

5.75

1.27

1.70±0.30

0.80±0.20

Φ7.40

7.40

1.65

2.00±0.30

0.95±0.20

Φ10.80

10.80

2.00

2.30±0.40

1.10±0.20

Φ12.00

12.00

2.41

2.45±0.40

1.20±0.20

Φ14.00

14.00

3.50

2.50±0.40

1.20±0.30

​Φ17.78

17.80

4.20

2.60±0.40

1.35±0.30

*Wall thickness will be less if tubing recovery is restricted during shrinkage.

注意: INERGEK は、適切と思われる変更を加える権利を留保します。
🌐 www.inergek.com    ✉ [email protected]    ☎ +86 189 7105 6957
INERGEK
INDUSTRIAL ENGINEERING & CONNECTIVITY
部品番号
SBRS-(4X)GRH
注意: INERGEK は、適切と思われる変更を加える権利を留保します。
🌐 www.inergek.com    ✉ [email protected]    ☎ +86 189 7105 6957